Transport reference
UN 1202 — Gas oil or diesel fuel or heating oil, light (flash-point not more than 60 °C)
Table A of ADR 2025 and the 49 CFR 172.101 Hazardous Materials Table for this number, kept side by side and never merged, plus the CLP label elements of the substances that ship under it.
The two tables are never merged. The same UN number can carry a different packing group, a different proper shipping name and entirely different special provisions in each system. Every value below sits under the name of the jurisdiction it comes from.
01 · Two jurisdictions
UN 1202 in ADR 2025 and in 49 CFR 172.101
The two systems differ for this number on 1 of 5 fields. Special provisions are deliberately absent from this comparison: identical code numbers mean different things in the two systems.
| Field | ADR 2025 Table A, Chapter 3.2 | 49 CFR 172.101 eCFR 2026-08-03 |
|---|---|---|
| Proper shipping name | GAS OIL or DIESEL FUEL or HEATING OIL, LIGHT (flash-point not more than 60 °C) · DIESEL FUEL complying with standard EN 590:2013 + A1:2017 or GAS OIL or HEATING OIL, LIGHT with a flash-point as specified in EN 590:2013 + A1:2017 · GAS OIL or DIESEL FUEL or HEATING OIL, LIGHT (flash-point more than 60 °C and not more than 100 °C) | Diesel fuel · Gas oil · Heating oil, light |
| Class or division | 3 | 3 |
| Packing group | III | III |
| Label codes | 3 | 3 |
| Rows in the table | 3 | 3 |
Sources: ADR 2025, Table A of Chapter 3.2 · ECE/TRANS/352 Vol. I (UNECE) · 49 CFR 172.101 Hazardous Materials Table · eCFR, revision 2026-08-03
02 · ADR 2025
UN 1202 in Table A of ADR 2025
3 separate rows in Table A of Chapter 3.2. They are not interchangeable: the packing group follows from the properties of the consignment, and each row carries its own transport category — that is a different multiplier in the 1.1.3.6 calculation.
| Proper shipping name (3.1.2) | Class | Classification code | PG | Labels | Transport category | Hazard ID |
|---|---|---|---|---|---|---|
| GAS OIL or DIESEL FUEL or HEATING OIL, LIGHT (flash-point not more than 60 °C) | 3 | F1 | III | 3 | 3 | 30 |
| DIESEL FUEL complying with standard EN 590:2013 + A1:2017 or GAS OIL or HEATING OIL, LIGHT with a flash-point as specified in EN 590:2013 + A1:2017 | 3 | F1 | III | 3 | 3 | 30 |
| GAS OIL or DIESEL FUEL or HEATING OIL, LIGHT (flash-point more than 60 °C and not more than 100 °C) | 3 | F1 | III | 3 | 3 | 30 |
Source: ADR 2025, Table A of Chapter 3.2 · ECE/TRANS/352 Vol. I (UNECE). Class 3 is “Flammable liquids” (ADR 2.1.1.1).
Transport category and the 1 000-point exemption
Column (15) of Table A decides whether a load stays under the exemption of ADR 1.1.3.6. Quantities of different categories are added with the multipliers below, and the sum must not exceed 1 000.
| Category | Max total quantity per transport unit | Multiplier in 1.1.3.6.4 | What it means |
|---|---|---|---|
| 3 | 1 000 | × 1 | Packing group III and the listed classes. |
Source: ADR 2025, 1.1.3.6.3 and 1.1.3.6.4 · ECE/TRANS/352 Vol. I (UNECE).
Special provisions — ADR 2025, Chapter 3.3
Codes from column (6) of Table A, with the text of Chapter 3.3.1. These are ADR provisions only. A code with the same number exists in 49 CFR 172.102 and means something else there — the two lists are never combined.
| SP 640K | The physical and technical characteristics mentioned in column (2) of Table A of Chapter 3.2 determine different tank codes for the carriage of substances of the same packing group in ADR tanks. In order to identify these physical and technical characteristics of the product carried in the tank, the following shall be added, to the particulars required in the transport document, only in case of carriage in ADR tanks: "Special provision 640X" where "X" is the applicable capital letter appearing after the reference to special provision 640 in column (6) of Table A of Chapter 3.2. These particulars may, however, be dispensed with in the case of carriage in the type of tank which, for substances of a specific packing group of a specific UN number, meets at least the most stringent requirements. |
| SP 640L | The physical and technical characteristics mentioned in column (2) of Table A of Chapter 3.2 determine different tank codes for the carriage of substances of the same packing group in ADR tanks. In order to identify these physical and technical characteristics of the product carried in the tank, the following shall be added, to the particulars required in the transport document, only in case of carriage in ADR tanks: "Special provision 640X" where "X" is the applicable capital letter appearing after the reference to special provision 640 in column (6) of Table A of Chapter 3.2. These particulars may, however, be dispensed with in the case of carriage in the type of tank which, for substances of a specific packing group of a specific UN number, meets at least the most stringent requirements. |
| SP 640M | The physical and technical characteristics mentioned in column (2) of Table A of Chapter 3.2 determine different tank codes for the carriage of substances of the same packing group in ADR tanks. In order to identify these physical and technical characteristics of the product carried in the tank, the following shall be added, to the particulars required in the transport document, only in case of carriage in ADR tanks: "Special provision 640X" where "X" is the applicable capital letter appearing after the reference to special provision 640 in column (6) of Table A of Chapter 3.2. These particulars may, however, be dispensed with in the case of carriage in the type of tank which, for substances of a specific packing group of a specific UN number, meets at least the most stringent requirements. |
| SP 664 | When substances under this entry are carried in fixed tanks (tank-vehicles) or demountable tanks, these tanks may be equipped with additive devices. Additive devices: - Are part of the service equipment for dispensing additives of UN No. 1202, UN No. 1993 packing group III, UN No. 3082 or non-dangerous substances during discharge of the tank; - Consist of elements such as connecting pipes and hoses, closing devices, pumps and dosing devices which are permanently connected to the discharge device of the tank’s service equipment; - Include means of containment which are an integral part of the shell, or permanently fixed to the exterior of the tank or tank-vehicle. Alternatively, additive devices may have connectors for connecting packagings. In this latter case, the packaging itself is not considered part of the additive device. The following requirements shall apply depending on the configuration: (a) Construction of the means of containment: (i) As an integral part of the shell (e.g. a tank compartment), they shall meet the relevant provisions of Chapter 6.8. (ii) When permanently fixed to the exterior of the tank or to the tank-vehicle, they are not subject to the construction provisions of ADR provided they comply with the following provisions: They shall be made of a metallic material and comply with the following minimum wall thickness requirements: Material Minimum wall thicknessa Austenitic stainless steels 2.5 mm Other steels 3 mm Aluminium alloys 4 mm Pure aluminium of 99.80 % 6 mm a For means of containment made with double walls, the aggregate thickness of the outer metal wall and the inner metal wall shall correspond to the wall thickness prescribed. Welding shall be carried out in accordance with the first paragraph of 6.8.2.1.23, except that other suitable methods may be applied to confirm the quality of the welding. (iii) Packagings which are connectable to the additive device shall be metal packagings and meet the relevant construction requirements of Chapter 6.1, as applicable for the additive concerned. (b) Tank approval For tanks equipped or intended to be equipped with additive devices, where the additive device is not included in the original type approval of the tank, the provisions of 6.8.2.3.4 shall apply. (c) Use of means of containment and additive devices (i) In case of (a) (i) above, no additional requirements. (ii) In case of (a) (ii) above, the total capacity of the means of containment shall not exceed 400 litres per vehicle. (iii) In case of (a) (iii) above, 7.5.7.5 and 8.3.3 shall not apply. The packagings may only be connected to the additive device during discharge of the tank. During carriage, the closures and connectors shall be closed so as to be leaktight. (d) Testing for additive devices The provisions of 6.8.2.4 shall apply to the additive device. However, in case of (a) (ii) above, at the time of the initial, intermediate or periodic inspection of the tank, the means of containment of the additive device shall only be subject to an external visual inspection and a leakproofness test. The leakproofness test shall be carried out at a test pressure of at least 0.2 bar. NOTE: For the packagings described in (a) (iii) above, the relevant provisions of ADR shall apply. (e) Transport document Only the information required in accordance with 5.4.1.1.1 (a) to (d) needs to be added to the transport document for the additive concerned. In this case, the remark "additive device" shall be added to the transport document. (f) Training of drivers Drivers who have been trained in accordance with 8.2.1 for carriage of this substance in tanks need no additional training for the carriage of the additives. (g) Placarding or marking Placarding or marking of the fixed tank (tank-vehicle) or demountable tank for the carriage of substances under this entry in accordance with Chapter 5.3 is not affected by the presence of an additive device or the additives contained therein. |
Source: ADR 2025, Chapter 3.3 special provisions · ECE/TRANS/352 Vol. I (UNECE)
Not imported and therefore not shown for this number: limited quantities (column 7a), excepted quantities (7b), packing instructions (8), tank codes (10–13) and the tunnel restriction code (15). An empty section is more honest than borrowed text.
03 · United States
UN 1202 in the 49 CFR 172.101 Hazardous Materials Table
3 separate rows in the Hazardous Materials Table. Where the rows differ only by the symbol in column (1), that symbol is what tells them apart — “D” is domestic-only, “I” is international.
| Symbols (1) | Proper shipping name (2) | Class (3) | PG (5) | Labels (6) | Packaging (8) | Quantity limits (9) | Vessel stowage (10) |
|---|---|---|---|---|---|---|---|
| I | Diesel fuel | 3 | III | 3 | §173.150 · §173.203 · §173.242 | 60 L passenger 220 L cargo | A |
| — | Gas oil | 3 | III | 3 | §173.150 · §173.203 · §173.242 | 60 L passenger 220 L cargo | A |
| — | Heating oil, light | 3 | III | 3 | §173.150 · §173.203 · §173.242 | 60 L passenger 220 L cargo | A |
Source: 49 CFR 172.101 Hazardous Materials Table · eCFR, revision 2026-08-03. Class 3 is “Flammable and combustible liquid” (49 CFR 173.2). Packaging cells are section references into 49 CFR part 173: exceptions, non-bulk, bulk. Handling codes in column 10B are defined in 49 CFR 176.84, which is not part of our import — the numbers are shown as printed in the table.
What the column (1) symbols mean
| I | International. A proper shipping name appropriate for describing materials in international transportation. An alternate proper shipping name may be selected when only domestic transportation is involved. |
Source: 49 CFR 172.101(b) · eCFR, revision 2026-08-03
Vessel stowage categories on this entry
| A | May be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel. |
Source: 49 CFR 172.101(k) · eCFR, revision 2026-08-03
Special provisions — 49 CFR 172.102
Codes from column (7) of the Hazardous Materials Table, with the text of § 172.102. These are United States provisions only and have nothing to do with the ADR codes above, even where the number is identical.
| 144 | If transported as a residue in an underground storage tank (UST), as defined in 40 CFR 280.12, that has been cleaned and purged or rendered inert according to the American Petroleum Institute (API) Standard 1604 (IBR, see § 171.7 of this subchapter), then the tank and this material are not subject to any other requirements of this subchapter. However, sediments remaining in the tank that meet the definition for a hazardous material are subject to the applicable regulations of this subchapter. |
| B1 | If the material has a flash point at or above 38 °C (100 °F) and below 93 °C (200 °F), then the bulk packaging requirements of § 173.241 of this subchapter are applicable. If the material has a flash point of less than 38 °C (100 °F), then the bulk packaging requirements of § 173.242 of this subchapter are applicable. |
| IB3 | Authorized IBCs: Metal (31A, 31B and 31N); Rigid plastics (31H1 and 31H2); Composite (31HZ1 and 31HA2, 31HB2, 31HN2, 31HD2 and 31HH2). |
| T2 | Portable tank instruction. Minimum test pressure: 1.5 bar; minimum shell thickness (reference steel): § 178.274(d)(2); pressure-relief requirements: Normal; bottom opening requirements: § 178.275(d)(3). See 49 CFR 172.102(c)(7)(ii), Table of Portable Tank T Codes T1-T22. |
| TP1 | The maximum degree of filling must not exceed the degree of filling determined by the following: |
Source: 49 CFR 172.102 special provisions · eCFR, revision 2026-08-03
04 · Orange plate
The orange-coloured plate for UN 1202
The upper half of the plate carries the hazard identification number, the lower half the UN number. Dimensions follow ADR 5.3.2.2.1: 400 × 300 mm, black border and dividing line 15 mm, figures 100 mm high.
30 — flammable liquid (flash-point between 23 °C and 60 °C, inclusive) or flammable liquid or solid in the molten state with a flash-point above 60 °C, heated to a temperature equal to or above its flash-point, or self-heating liquid.
| 3 | Flammability of liquids (vapours) and gases or self-heating liquid |
| 0 | No further hazard — the first figure alone describes the hazard adequately |
Source: ADR 2025, 5.3.2.3 · ECE/TRANS/352 Vol. II (UNECE). The tunnel restriction code of column (15) is a different value and is not part of our import.
05 · Substances
Substances shipped under UN 1202
Linked by CAS number, never by name: a name match once produced “acetone cyanohydrin” for acetone, and a wrong link here would be a wrong classification. Each entry opens its own reference page with the CLP classification and label elements.
06 · The label side
What UN 1202 looks like on a workplace label
The tables above are the transport classification. This is the other half of the same material: the CLP label elements of the substances linked to this number — what actually goes on the drum once it has been delivered. Transport marks and supply labels answer different regulations and do not replace one another.
Hazard statements on the substances under UN 1202
| H351 | Suspected of causing cancer <state route of exposure if it is conclusively proven that no other routes of exposure cause the hazard>. |
Source: harmonised classification, EU CLP Annex VI. Transport classification and supply classification are decided under different rules and do not have to agree.
07 · FAQ
UN 1202 — frequently asked questions
What is UN 1202?
UN 1202 is the United Nations number for Gas oil or diesel fuel or heating oil, light (flash-point not more than 60 °C). Under ADR 2025 it is assigned to class 3 (flammable liquids), classification code F1.
What packing group is UN 1202?
Under ADR 2025 UN 1202 is packing group III.
Is UN 1202 classified the same way in the United States and in Europe?
No. For UN 1202 the two tables differ on proper shipping name. Each panel on this page shows its own source; values from one system must not be carried over into the other.
What is the hazard identification number for UN 1202?
The orange-coloured plate for UN 1202 carries the hazard identification number 30 above the UN number. Under ADR 5.3.2.3.2 that number means: flammable liquid (flash-point between 23 °C and 60 °C, inclusive) or flammable liquid or solid in the molten state with a flash-point above 60 °C, heated to a temperature equal to or above its flash-point, or self-heating liquid.
What is the transport category of UN 1202?
Column (15) of Table A puts UN 1202 in transport category 3. Under ADR 1.1.3.6.3 the maximum total quantity per transport unit for that category is 1 000.
Which substances ship under UN 1202?
We hold 1 substance linked to UN 1202 by CAS number, 1 of which also has a full safety data sheet on this site. Each one has its own reference page with the CLP classification, GHS pictograms and hazard statements that apply on the label — the workplace side of the same material.
Need the plate, the labels or the placards printed?
The orange plate above is a physical article, and so are the class labels in column (5). Our sister site GHSLabels.com covers printing and suppliers. For the workplace label of the same material, use the GHS label constructor, and browse other numbers in the UN number reference.
Reference aid only. Values are reproduced from ADR 2025 and the 49 CFR 172.101 table as published; the consignor remains responsible for the classification of a specific consignment. Always verify against the current published regulation and the supplier's safety data sheet.